Registrations

The registration screen contains the registrations retrieved from the blackboxes.

Open registration screen

The registration screen can be opened for one or more ships, in the following ways in both the presentation and service station:

• From the ship overview → Info → Registrations;
• From the deviations screen → Info → Registrations.

In the service station the registration screen can also be opened for one ship, by right clicking the mouse in the ship overview and choose Registrations from the pop up menu.

After the desired period selection has been entered, the screen will be opened.

Registration screen content

Depending on the fleet, available licenses and/or user, the following information about the registrations is shown in list view:

Column	Content	Available in BPS	Available in BSS	Available in BMS	Fleet/User Dependent
Ship	The ship code	X	X	X
Datetime registration	The date and time of the registration	X	X	X
Datetime blackbox	The date and time registered in the blackbox		X	X
Next reg	If the next registration is missing or not: - : next registration is missing - empty cell: next registration is available	X	X	X
Previous reg	If the prevoius registration is missing or not: - : previous registration is missing - empty cell: previous registration is available	X	X	X
Delta	The time difference between the Datetime registration and Datetime blackbox: - 0: no difference - -1: 1 second difference		X	X
Incidental registration			X	X
Registration interval			X	X
Missing interval registration			X	X
Expected interval to next registration			X	X
Latitude	Latitude of the position in [G]G MM.MMMMM N/S	X	X
Longitude	Longitude of the position in [GG]G MM.MMMMM E/W	X	X
Speed	Speed over ground ​​(SOG) in knots	X	X
Gps quality code	Quality of the gps in code, see Gps quality code and text		X	X
Gps quality	Quality of the gps in text, see Gps quality code and text		X	X
Missing gps	If the gps position isn't available: - : gps position is missing, see column Alarm notification - empty cell: gps position is available	X
Ship status code	(Calculated) Status of the ship in code, see Ship status code and text	X	X	X
Ship status	(Calculated) Status of the ship in text, see Ship status code and text	X	X	X
BB ship state code	State of the ship in code, measured by the blackbox		X	X
BB state code	State of the blackbox system in code, see BB state code and text		X	X
BB state	State of the blackbox system in text, see BB state code and text		X	X
SOG status code	(Calculated) Speed over ground status in code, see SOG status code and text				X
SOG status	(Calculated) Speed over ground status in text, see SOG status code and text				X
COG status code					X
COG status					X
Battery supply	Voltage of the battery supply, noted in V. - Minimum value: 0.1V - Maximum value: 25.0V		X	X
Charge supply	Voltage of the charge supply, noted in V - Minimum value: 0.1V - Maximum value: 25.0V		X	X
External supply	Voltage of the external/vessel supply, noted in V - Minimum value: 15V - Maximum value: 40.0V		X	X
Turbo pressure	(Calculated) Turbo pressure based on the input configurations in the configuration				X
TP status code	(Calculated) turbo pressure status in code, see TP status code and text				X
Turbo pressure status	(Calculated) turbo pressure status in text, see TP status code and text				X
Shaft power	(Calculated) Shaft power based on the input configurations in the configuration				X
PPstatus 1/2					X
Sea status code					X
Sea status					X
Sea area					X
N2000 area					X
Fish activity status code					X
Fish activity status					X
Engine check					X
Gsm action	Action of the gsm, possible actions are: - Data request: blackbox received a data request - Paramaters changed: the parameters have changed - Monitor mode: monitor mode is active - Software update: software is updated - Command received: blackbox received a command - Modem initialization: modem is initialized - Modem failure: modem is not working		X	X
Gsm quality code	Quality of the gsm connection in code, see Gsm quality code and text		X	X
Gsm quality	Quality of the gsm connection, see Gsm quality code and text		X	X
Sms action	Action of the sms, possible actions are: - Sms sending: a sms is send - Service failure: the service number initialization failed - Sms failure: sending an sms has failed		X	X
Board temperature	Temperature of the board supply, noted in °C - Minimum value: -20°C - Maximum value: +100°C		X	X
Battery capacity	Capacity of the battery supply, noted in % - Minimum value: 0% - Maximum value: 100%		X	X
Battery temperature	Temperature of the battery supply, noted in °C - Minimum value: -20°C - Maximum value: +100°C		X	X
Battery current	Charge current of the battery supply, noted in mA - Minimum value: -1280mA - Maximum value: 1270mA		X	X
Alarm	If an alarm occured: - : an alarm occured, see column Alarm notification - empty cell: no alarm occured		X	X
Alarm notification	Type of alarm that occured, see Alarms		X	X
RPM ​​1/2	(Calculated) RPM 1/2 value based on the input configurations in the configuration		X
Calculated TP fishing					X
Calculated TP sailing					X
TP fishing difference					X
TP sailing difference					X
Calculated SP fishing					X
Calculated SP sailing					X
SPFDiff					X
SPSDiff					X
Calling Index			X	X
Duty cycle 1/2	Duty cycle 1/2 measured by the blackbox, noted in percentage - Minimum value: 0% - Maximum value: 25%				X
Pulse input 1/2	Pulse input 1/2 measured by the blackbox, noted in mHz - Minimum value: 0 mHz - Maximum value: 10.000.000 mHz				X
Analogue input 1 to X			X	X

Gps quality code and text

Gps quality code	Meaning in text
0	No gps data available
1	No valid position available
2	2D fix without D
3	3D fix without D
4	2D fix with D or PPS
5	3D fix with D or PPS
6	Gps antenna has an open circuit
7	Gps antenna has a short circuit

Ship status code and text

Ship status code	Meaning in text
0	Unknown
1	Stationary
2	Fishing
3	Sailing
4	Transition
5	Undetermined
6	Possible fishing

BB state code and text

BB state code	Meaning in text
0	Normal
1	Standby
2	Off
3	Fast standby

SOG status code and text

SOG status code	Meaning in text
0	Unknown
1	Stationary
2	Fishing
3	Sailing
4	Transition

TP status code and text

Ship status code	Meaning in text
0	Unknown
2	Fishing
3	Sailing
5	Undetermined

Gsm quality code and text

Gsm quality code	Meaning in text	signal strength range
0	Bad	no signal
1	Moderate	-103 dB to -113 dB
2	Reasonable	-72 dB to -102 dB
3	Good	-51 dB to -73 dB

Alarms

Alarm	Cause	Fleet/user dependent
Cold reset	The system has been reset after restart or a (temporary) power loss of the vessel and battery supply
Warm reset	The system has been reset after the watchdog was triggered, a voltage dip or software reset has occurred
Watchdog reset	TThe system has been reset after the watchdog was triggered
Software reset	The system has been reset by the software. This is done to restart the GPS receiver at power-up, when the antenna state is not known
Low voltage reset	The system has been reset without powering down after a voltage dip
Deep sleep reset
Default configuration loaded	The default configuration parameters are loaded into the system after a configuration or SD card failure during configuration
New configuration changed	A new configuration has been uploaded to the system
No gps data	The system couldn't receive gps data, because of a missing or broken gps receiver
Gps bad signal
Gps antenna failure	The gps antenna has a short or open circuit
Power failure
Ext supply low	The vessel supply is lower than 22V
Battery supply low	The battery supply is lower than 11.2V or 11.7V during blackbox state 'normal'
Internal supply failure	Internal supply or VCC failure
SD card error	The system cannot read or write to the SD card
Sleep RAM memory error	The system cannot read the settings from the RAM after booting
RTC wake-up error
Enclosure open	The enclosure of the blackbox is opened
Accept input	An alarm has been manually accepted on the blackbox
Modem failure
Sms failure
Internal temp too high	The temperature of the internal supply is higher than 60°C
Battery temp too high	The temperature of the battery supply is higher than 60°C or lower than -15°C
Buzzer on	The buzzer is active
Namur 1/2 error
Calibration		X
Moving during standby
Special 1
Special 2
Special 3
No battery detected
External supply error
Battery capacity error
Battery temperature error
Battery current error
Battery supply error
Board temperature error
Charge supply error
Analogue input 1 to X low alarm
Analogue input 1 to X high alarm

Retrieve registrations

Only available in: BSS and BMS

Registrations are automatically retrieved if the ship's end date has been entered and has not yet expired. When a ship is behind with the registration data, it is possible to retrieve them manually from a blackbox, when the blackbox is connected.

Retrieve last blackbox registrations

Retrieving the last blackbox registrations manually is currently possible for one ship at a time. To retrieve registrations for a specific ship, right click on the ship in the ship overview screen and click Retrieve last blackbox registrations. The following screen opens, in which the statusses of the processes are shown:

If a connection can be made with the blackbox, the binairy data will be retrieved directly from the blackbox, from the last registration date stated under the column 'Last registration'. The registrations are automatically converted into usable data after retrieval (ProcessRegistrations). Finally, the necessary calculations on the data are performed (PostProcessRegistrations).

When the calculations are complete, you can click OK to close the window and return to the ship overview. If you want to cancel the process in the meantime, click on Cancel. The registrations will be retrieved, processed and/or postprocessed up to the point of cancellation.

Retrieve last blackbox registrations (period)

User dependent.

Under construction

Recalculate registrations

Only available in: BSS and BMS

Recalculate registrations manually is currently possible for one ship at a time. To recalculate registrations for a specific ship, right click on the ship in the ship overview screen and click Recalculate registrations. After the desired period selection has been entered, the following screen opens, in which the statusses of the processes are shown:

The binairy data of the registrations will be converted into usable data (ProcessRegistrations) and the necessary calculations on the data are performed (PostProcessRegistrations).

When the calculations are complete, you can click OK to close the window and return to the ship overview. If you want to cancel the export in the meantime, click on Cancel. The registrations will be processed and/or postprocessed up to the point of cancellation.

Registration data chart

Only available in: BSS and BMS

Information on the general use of graphs can be found here: Using the charts.

From registration screen the registration data chart can be opened for one ship clicking on the menu item Tools → Chart view → Registration data. If there is data for more than one ship in the registration screen, you can select the desired ship and open the chart.